Resultats 1 - 12 sur un total de 498 réponses pour hobbyking minimoa motor screws

It depends on what ASP say about the engine.We take photos and show them to ASP, then either send it back to them or replace the motor straight away, depending on what they request.As I don't have your details, it's best for you to contact support about this.3 months is a very long time. Our standard warranty turnaround is 14 days. Please contact support.

Hi, Chris,I would say this fan motor combination would fly you model with ease ,first you will need to diassemble rotor ,motor from fan shroud.Then balance fan rotor very accuratly .Next drill a 2mm hole at end of aly shaft so you can put allen key in this hole so you can tighten hex nut to hold on rotor use a little locktite type compound on this nut as w ell as grub screws that holds fan shaft to motor shaft.When you reinstal motor in fan shroud make sure shaft is on centre to inside of[...]

bearing failure often is related to lubricant- wrong type for app , where app is load AND rpm.really, nothing except for bearings should wearout in a motor. and the bearings should take a long time (number of cycles).if high rpm is wearing the bearings then you've not selected the correct bearing for the application.

The ultra light and ultra small Micro F4 jet comes as a kit and will take you 1 evening to complete. Included is a 40mm EDF and brushless inrunner motor. Just include your own ESC, 2.5g servos and receiver. Specifications: Length : 540mm (21.3in) Wing Span: 340mm (13.4in) Flying Weight: 90~107g (with battery)  ESC: 18Amp required  EDF: 40mm Inrunner motor 10,000kv (Included) Servo: 2x2.5g required    Required: Your own TX & RX 7.4V[...]

Heres a question that nobody has asked.   With a twin, it is fairly evident that with manufacturing tolerances being what they are, how are you going to cope with a low voltage cut off on one esc occuring before the other?   This is similar to one gas/glow motor failing and often results in the loss of the aircraft. ( The so-called 'DEATH SPIRAL'   I have the Hangar 9 Mitchell twin. It is on electric. It incorporates most of the ideas mentioned in this[...]

Hay, Can somebody out ther give me some advice? I am building a Nexstar e/p and I was wondering what Turnigy motor would be best to use when it calls for either a .46 or a rimfire 42-50-800. Sometimes the info given doesn't tell you all you need to know in the motor description.

I ask this question to every one :When could we see  EDF Jet from Freewings models with Thrust vectoring on HobbyKing ?I think they are the best Jet with RC Lander.It will be nice to see some  new  EDF jets  for experience pilots :-)

I have a problem with the turnigy e5006t motor slipping away on the motor mount from the main gear whenever i power up. I've been using washers but the washers are a little big for the screws. Should i just go back to using no washers? I only had trouble once with no washers and i think it it might have been because of me flipping idleup too early because of my non programmable transmitter had preset idleup. Suggestions? Thanks

From this combo.  http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=10330&Product_Name=Brushless_Car_Power_System_5200Kv/100AI already have the combo, and would like to buy a few extra motors for other cars.  Can I buy just the motor separately?

Hello:   Can someone tell me if this spinner will work OK on a Turnigy 35-30?   http://www.hobbyking.com/hobbycity/store/uh_viewItem.asp?idproduct=9150#12   I know it will fit the shaft OK, but I am wondering if it is too heavy since I see others are using it on nitro engines??   Thanks, Garret

You guys know that someone who's not in the hobby won't have the first clue what to get you for christmas. Would you support a gift card for hobbyking. It would be extremely simple to make just weave it into the credit system hk already has.Just a suggestion

The Me-109 RTF comes complete with brushless motor, ESC and all servos installed. Assembly of the Me-109 wing, canopy and tail can be done in 15 minutes. Include your own battery and receiver to be ready for your first flight in under 30 minutes!   Specifications: Fuselage Length : 720 mm Wingspan : 890mm Flying Weight : 450g  Power system  : 370A brushless outrunner ESC: 18A Propeller : 8x6 Battery : 2 cells 7.4V - 1300mAh Li-Po (Not[...]